The Construction Products Regulation (CPR)

 

FAQs and information

From 1st July 2017 cable manufacturers are obliged to test power cables and lines as well as control and communication cables for reaction to fire performance requirements in accordance with the new harmonised Standard EN 50575, and to classify and market them with a Declaration of Performance (DoP in short).

Below we answer the questions we are most frequently asked in this context.

  • What does “CPR” stand for?

    “CPR” stands for “Construction Products Regulation” (EU 305/2011).

  • What is a construction product?

    A construction product is any product marketed for permanent installation into construction works or parts thereof, and the performance of which affects the following basic requirements of construction works:

    - Mechanical strength and stability
    - Fire protection (fire safety)
    - Hygiene, health and environmental protection
    - Safety and accessibility in use
    - Noise insulation
    - Energy economy and heat retention
    - Sustainable use of natural resources

    The performance of cable products affects the basic requirement of “fire protection” in construction works.

  • When does the CPR for cables take effect?

    The Construction Products Regulation takes effect on 1st July 2017. After that manufacturers are no longer permitted to place cables for “fixed installation” in construction works on the European market without a CE marking and “Declaration of Performance” (DoP).

    Safety cables with insulation integrity or functional integrity (System Circuit Integrity) are still currently exempt, as the necessary standards are not yet available.

  • To what types of cable does the CPR apply?

    The Construction Products Regulation applies to all power, control and data cables and lines permanently incorporated in construction works (fixed installation). “Fixed installation” covers all known exposed types of installation as well as surface- and flush-mounted installations.

  • Which cables are not covered by the CPR?

    Cables not intended for permanent use in buildings are generally exempt from the requirements of the CPR, for example:

    - Patch cables (patch cords)
    - Cable systems covered by the Machinery Directive (e.g. lift cables)
    - Cables not intended for use in construction works (e.g. outdoor cables)
    - Flexible cables to devices, lights or machines
    - Cables leading to consumers via connectors
    - Safety cables with insulation integrity and/or functional integrit

    “Safety cables” are currently exempt from the requirements of the CPR.

    According to EN 50575 “Cables intended to be used for the supply of electricity, communication, and fire detection and alarm in buildings and other civil engineering works where it is essential to assure the continuity of power and/or signal supply of safety installations such as alarm, way guidance and fire fighting installations are not covered by this standard.”

    Work is under way on the appropriate standards for safety cables with insulation integrity and/or functional integrity (System Circuit Integrity).

  • How is CPR testing carried out?

    The EU Commission has approved European test laboratories as notified bodies to test and evaluate the reaction to fire performance of cables for this additional task.

    The product characteristics of a “construction product” cable must be determined and confirmed by a notified body. By the same token the manufacturer’s production facility must be subject to ongoing production control by the notified body.

    Following product assessment and production monitoring the notified body authorises the manufacturer to deliver his products with the CE mark and to issue a Declaration of Performance (DoP).

  • Which fire classes are specified in the standards under the CPR?

    In accordance with EN 50575 the fire classes so far known for construction products (e.g. A1, A2, B1, B2, and B3 in Germany) are replaced by seven new classes for cable products. The following criteria are evaluated when testing is carried out in compliance with EN 50575:

    - Heat of combustion
    - Thermal release
    - Vertical flame propagation
    - Smoke generation
    - Flaming droplets/particles of plastics materials which can contribute to fire propagation
    - Acidity

    The results of this test should be assigned to the following cable classes:

    Main class Description
     Aca Non-flammable, no contribution to fire; products such as mineral-insulated cables and lines
     B1ca Low flammability, very limited contribution to fire
     B2ca, Cca Very limited or limited contribution to fire; cables/ lines without continuous flame propagation; limited fire development and thermal release rate
     Dca Acceptable contribution to fire; products with continuous fire propagation; moderate fire development and thermal release rate
     Eca Normally flammable; cables and lines with acceptable fire behaviour which have flame-retardant characteristics when exposed to a small pilot flame
     Fca Easily flammable; this cable can ignite when exposed to a small flame
  • What additional requirements and classes are there?

    Additional classifications are to be determined for classes B1ca to Dca.

    The fire-critical parameters have been identified as smoke generation, flaming droplets of cable material and the acidity of the combustion gases:

    Additional classes for smoke generation in cables:
    s1 Slight smoke generation
    s2 Moderate smoke generation
    s3 Severe smoke generation
    Additional classes for flaming droplets/particles in cables:
    d0 No flaming droplets
    d1 Short-lived flaming droplets
    d2 Persistent flaming droplets
    Additional classes for acidity in cables:
    a1 Slightly corrosive flue gases
    a2 Moderately corrosive flue gases
    a3 Severely corrosive flue gases
  • What is the recommended application of each of the new “Euroclasses”?

    The Construction Products Regulation (CPR) regulates the placing of construction products on the market – but not their use in construction work. The selection and use of construction products are the responsibility of the European Member States. The requirements governing which fire protection class is specified for which location therefore differ from country to country.

    Installers and specialist planners must check and comply with the relevant local regulations.

    In many countries there are still no mandatory requirements governing the use of fire classes in buildings as from 1st July 2017. Where there are no minimum mandatory legal requirements, there are generally recommendations by the CPR professional associations for application in the relevant countries.

  • Which NEDIS products have which CPR classifications?

    For cable products in scope of the CPR you will find up-to-date information on the classification of our cable products on our website.

    In the online data sheets you will find icons for simple identification of the Euroclasses in which a product is covered (“main classes”). Reaction to fire performance conforming to EN 13501-6 (Euroclasses) – including the additional classifications – is shown in the data sheets under “Standards”.

  • Where do I get the data sheets and Declarations of Performance?

    For cable products in scope of the CPR  you will find the up-to-date data sheets on the NEDIS website.

    Declarations of Performance for cable products in scope of the CPR will be provided with the delivery documentation from 1st July 2017 at the latest. If a copy of the Declaration of Performance is needed it can be requested via the NEDIS contact address of the relevant country.

    From 1st July 2017 Declarations of Performance for cable products in scope of the CPR will also be available for downloading on the NEDIS website.

  • Are cable markings being changed?

    No, the labelling of cables does not form part of the CPR.

    Cable designations are specified by the relevant design standards of the country of manufacture.

  • Can cables without “CPR classification” bought before 1st July 2017 still be installed?

    These cables may still be installed and used providing there are no national requirements relating to the use of classified cables under Construction Products Regulation.

    If there already are national requirements relating to application, the use of cables without “CPR classification” should be clarified with the authorities responsible.

  • Can cables without “CPR classification” placed on the market before 1st July 2017 be sold on or traded?

    Cables covered by the CPR but placed on the European market before 1st July 2017 and bearing the CE mark in accordance with the Low Voltage Directive (LVD) may continue to be sold on for an indefinite period.